89321 Firmware Release Note: Firmware version : 100a-090F Firmware build : 10/12/2005 firmware release date : 10/27/2005 First release official firmware for Axus 89321 ````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Firmware version: 101a-0B13 Firmware build : 11/10/2005 firmware release date : 11/16/2005 Update function: RAID kernel: 1. Modify the wording of system info message from "write buffer" to "Write cache". 2. Fix the issue=>Enable SMART function and save to NVRam. Restart system, the SMART function still show "Disable. 3. Fix the issue=>In "clone function", the "Source disk" should only show arrays member disks and the "Target disk" should only show the spare disks. 4. Fix SANMask malfunction problem. BugID:89320-148 5. Fix multiple lun mapping issue. 6. Modify the SATA driver to compatible with Marvell 6081 revision B2 and C0. 7. Display the messages of "You need to restart to apply factory defaults" on hyper terminal when users execute "Factory Default" menu function. (BugID:89320-146) 8. Fix for passing WHQL (scsicompliancetest). (with LSI/QLOGIC FC HBA) (BugID:AR89320_017, 89320_150) 9. Remove the wording "LSI firmware release informations ¡K Vendor do not release 9/23/2005". (BugID:89320-151) 10. Remove redundant and FC chip relative menu. (BugID:89320-152) 11. Fixed Irq24 lock issue when using specfic switch (Accton). (BugID:89320_149) GUI: 1. In [Comm Params], only show dialog when these parameters([DHCP], [IPAddress], [Subnet Mask], and [Gateway IP Address]) are changed. 2. In [Comm Params], disallow setting these parameters([IP Address],[Subnet Mask], [Gateway IP address], and [DNS IP Address]) if the parameter [DHCP] is enabled. 3. In [Disk Self Test], fix the bug about showing percentage of DST. 4. In [Disk Self Test], refresh the table when the combo box "DST Mode" is in "Stop Test". 5. In [Disk Clone], refresh the table when the combo box "Clone Mode" is in "Stop or Cancel". 6. Change the term "Terminator" to "Terminal". 7. In [Shutdown], hide the BBM status when the BBM is not supported. 8. In [Notify Params], send the test mail after all other parameters are sent. 9. In [Monitor], fix the bug about incorrect background color of pop-up dialog. 10. In [Nodify Params], send commands even the notify is disabled. 11. In [Notify Params], ensure that all fields of IP address are lesser than 256. 12. In [Host Params], switch to the [Monitor] page after sent commands. 13. bug-89310-485:-> In [Disk Self Test], retain the selected status of rows when the table is refreshing. 14. Add wish-89310-433:-> In the left toolbar, hide the disabled menu items according to the model. 15. Never disable the menu item [Slice Setting], just disable the [Save and Restart] button in the page. 16. In [Quick Setup], fix some exceptions of the combo box [Loop ID]/[SCSI ID]. 17. Show both ID and Lun in [Monitor], [Delete Array], and [Array Info]. 18. Add wish-89310-132-1 and wish-89310-134-1:-> Support multiple SCSI ID setting. 19. Fix bug-89320-101:-> Fix the incorrect information of lun mapping when switching between arrays. 20. In [Quick Setup], change the term "IDs" to "SCSI ID". 21. Fix bug-89310-486, bug-89320-102:-> Switch to [Monitor] and lock the buttons [Login]/[Config] when the admin changing settings of [Host Params]. 22. Fix bug-89310-432, bug-89320-098:-> Modify the picture "Btn_Array_NotExist.gif". 23. Fix bug-89310-483, bug-89320-141:-> Modify the length of string buffer to 16. 24. Fix bug-89310-439, bug-89310-440:-> Change the bounds of incorrect Labels,ComboBox,TextFields and Buttons. 25. Fix bug-89310-438, bug-89320-113:-> Set location to the two windows to avoid overlap. 26. Fix bug-89310-498 and refix bug-89310-439:-> Change cache param's Label bounds and system param's Label bounds. 27. Fix bug-89310-497:-> Modify the validation rule of RTC settings. 28. Fix bug-89310-414:-> Don't allow user to change host channel ID in [Quick Setup] now. 29. Fix bug-89310-493 and bug-89320-101-1:-> The text field [Slice Capacity] will be disabled if there is no free slice number. 30. Fix bug-89320-110:-> Don't allow user to change host channel ID in [Quick Setup] now. 31. Fix bug-89320-127:-> User can apply slice setting before he click the [Save and Process] button. 32. Fix bug-AR89310-042 (Arena_033) and bug-AR89310-154:-> The [Select Drivers] & [Array Capacity(MB)] will be updated. 33. In [Quick Setup], the [Save and Process] button will be enabled if there is any editing array. 34. In [Quick Setup], when user click the [Apply] button, the combo box [Slice Number] will jump to next item which can be set/mapped. ```````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 102a-0C1B Firmware build : 01/24/2006 firmware release date : 02/13/2006 Update function: RAID kernel: 1. When setting slice size without saving to NVRAM, and then reselect RAID level and RAID members, then slice setting menu won't present. 2. Display the disk's serial number and firmware version on terminal and GUI function. 3. Read disk temperature via ATA SMART command and display it on the terminal and GUI function. 4. Fix a bug about setting model name. 5. Allow only the user set GUI password to log in to GUI. The other default special GUI passwords with special previleges are removed. 6. Disable GUI commands c3 and c6, because these commands were previously only accessilbe wit special GUI passwords. 7. When setting slice size without saving to NVRAM, and then reselect RAID level and RAID members, then slice setting menu won't present. 8. Display the disk's serial number and firmware version on terminal and GUI function. 9. Read disk temperature via ATA SMART command and display it on the terminal and GUI function. 10. Fix problem of incorrect disk state in LCD when plug in new disks and create/erase Array immediately. 11. Fix a bug about setting model name. 12. Fix problem of unexpected performance drop when flushing the write buffer or when user executes "view system info" or "event log" menu function. 13. Tuneing the FC parameter value to improve performance. 14. Support ¡§Alignment offset¡¨ function. 15. Fix a bug of incorrect disk numbers presented when "expand array" menu been selected. 16. Update GUI command and page data functions to the most recent GUI spec (version 1.27-13). 17. Add new function of "GUI Title Name" in the special menu. 18. Customer can changed GUI tool title via this menu function. (default is "RAID GUI") 19. Display the controller number on the LCD and "View SYS Info" menu function. 20. Fix a bug of error SAN masking on windows XP/2003. 21. In 89320 series, only "auto" can be selected in FC "set data rate" menu. 22. Modify the rule of read disk temperature via ATA SMART command to improve performance. (fix for performance may drop momentarily) 23. Fix a bug of clone function about cloned disk selection. 24. Fix a bug of command status displaying in Accusys menu. 25. Add a mechanism to prevent exception happened when hardware ID check error. 26. Add a mechanism to find the correct number of mapping luns when the host runs "Rescan Disks". 27. Fix the error message of "Divided by Zero in Kernel" in linux console when the host scan disks with R30/R50. 28. Fix a bug of menu title displaying. 29. If controller temperature over threshold, set all fans to full speed. 30. Fix a bug about the setting of Disk check time in smart function. GUI: 1. Disable all buttons of [Monitor] page when the controller is restarting. 2. If the disk has not tested yet, leave the two cells [Percent] and [Result] blank. 3. In [Disk Self Test], add one check-box [Select All Disks] to select all available disks. 4. In [Monitor], show "Serial Number", "Firmware Version", and "Temperature" in the dialog of [Disk Information] if the information are available. 5. Let the "Java Applet" warnning belt show below so it won't show up in fornt of the Main GUI screen. 6. Change the Array Button's Font from "Arail Plain" to "Courier NEW BOLD". 7. Switch to [Monitor] and lock the buttons [Login]/[Config] when the admin changine settings of [Notify Params] and [Restart]. 8. Separate controller chassis info from other chassis info. 9. Login when pressing "Enter" key in password field. 10. Fix bug. In [SanMask Params], show wwn and nickname correctly. 11. Fix bug. In [SanMask Params], restore deleting lun to lun's comboBox when the lun belong to the selecting HostPc. 12. Fix bug. In [SanMask Params], init "Support Host Chan X" value correctly. 13. Fix bug. In [SanMask Params], refresh "Support Host Chan X" value when change it. 14. Fix bug. In [SanMask Params], get array and slice information correctly when lun's ComboBox changed. 15. In [SanMask Params], save all WWN and Host Chan X settings if user presses "Save and Process". 16. In [SanMask Params], enable/disable "Apply" button now depend on HostPc and Lun ComboBox being null or not. (In one function) 17. In [SanMask Params], comboBox always select item if it has items. 18. In [Update F/W], open new browser window automatically when user click the button [Update Start]. 19. Remove the background and change the color when user click the button. 20. In [Cache Params], show current state of write cache. 21. In [Quick Setup], user can't enter incorrect value into the text field [Slice Capacity] now. 22. In [Comm Params]/[Notify Params], user can't enter value which larger than 255 into the text fields of [Ethernet Params]/[SMTP Server] now. 23. In [Disk Clone], the column [State] will be "Member"/"Spare" only if there is existed array. 24. Use "Scrubbing" instead of "Scrubing". 25. In [Monitor], clear the password field when user login with wrong password. 26. In [Quick Setup] & [Expand Array], the number of [Available Drives] will not count cloned drives. 27. In [Delete Array] & [Array Info], add " Sector " to the content of [Stripe Size]. 28. In [Quick Setup], modify the sequence of [Array Level] to match the sequence of terminal. 29. In [Delete Array], the GUI will show warning dialog when user click the button [Save and Process]. 30. In [Update F/W], correct the state of buttons [Update Start] & [Update Cancel] and allow user to cancel during transferring. 31. Enable the function of [Update F/W]. 32. In [Disk Self Test], if user want to switch to denied pages, the GUI will show "Disk is testing, you can't use this function now.". 33. In [Scrubbing Array], if the action is finished, user can switch to other pages, or the GUI will show "Array is scrubbing, you can't use this function now.". 34. If any array is expanding, user only can switch to these pages: [Monitor], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. 35. If any array is rebuilding, user only can switch to these pages: [Monitor], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. 36. Change blocking scenario as follows: a)If any array is initiating or rebuilding or expanding, user only can switch to these pages: [Monitor], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. b)If any array is scrubbing, user only can switch to these pages: [Monitor], [Scrubbing Array], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. c)If any disk is testing, user only can switch to these pages: [Monitor], [Disk Self Test], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. d)If any disk is cloning, user only can switch to these pages: [Monitor], [Disk Clone], [Disk Info], [Array Info], [System Info], [Comm Params], [System Params], and [Notify Params]. e)If the firmware is updating, user can't switch to any page. 37. In [SanMask Params], modify scenario of WWN table. The GUI will show all the setting including "0000 0000 0000 0000". 38. In [Host Params], change the term "ID" to "SCSI ID". 39. In [Comm Params]/[Notify Params], the GUI will limit the length of the text fields of [Ethernet Params]/[SMTP Server] to 3. 40. In [Quick Setup], add "None" option to the combo-box [SCSI ID] when the host channel is in multi-ID mode. 41. Change [Connection losing] scenario as follows: a. If the GUI fail to send command, the GUI will set the icon at left side to red and disable the buttons of [Monitor] page. b. If the GUI fail to receive reply, the GUI will set the icon at right side to red and disable the buttons of [Monitor] page. c. When the connection is restored, the GUI will enable the buttons of [Monitor] page and set the two icons to green. 42. Change [Expand Array] scenario as follows: a. If there is no existing array, all buttons will be disabled. b. The GUI will not hide the check-box [All Available] when user checks the check-box [Select All Chassis]. c. After user clicked the [Confirm] button, the GUI will disable the [Confirm] button and enable the [Save and Process] button. 43. In [Quick Setup] & [Expand Array], user can change the number of confirmed disks before he clicks the button [Save and Process]. 44. In [Quick Setup], if there is no available disk; the GUI will disable useless buttons. 45. In [Quick Setup] & [Expand Array], the GUI will enable the button [Confirm] only if the setting of selected array (after last confirm) is changed. 46. In [Quick Setup], once user confirmed the [Stripe Size], the GUI will not allow he to change the value. 47. Add program title and icon image. 48. Hide speed option if product type equals to 89320. 49. In [Delete Array] & [Array Info], all fields will align to left side. 50. When array fail occur, the GUI will show log "Array n is Fail. Please refer to trouble shooting about what should do when Array Fail occurs" to notice user. 51. If [Update F/W], change the font size of hine messages to 16px. 52. In [Delete Array] & [Array Info], remove the owner field. 53. In [Host Params], add function [Sector Per Track]. 54. The GUI will show array number, slice number, and channel number in event log now. 55. Add short/extended DST and background/foreground initiating message. 56. In [Disk Clone], display the owner array of source disks. 57. In Mac Safari, user can close the GUI and then re-open a new one without quitting the Safari fully now. 58. In Win IE, user can close the GUI and then re-open a new one without quitting the IE now. 59. In [Disk Info], the GUI will show the number of bad sectors. 60. In [Modify Array] & [Quick Setup], allow user to setup [Alignment Offset]. 61. In [Config] mode, add [Modify Array] page. 62. In [System Params], user can set time zone now. 63. In [Config] mode, add [Event Log] page to allow user to view and erase logs. 64. In [Delete Array], [Modify Array], and [Array Info], modify the text in the field [Status]. 65. Move the function [Sector per Track] from [Host Params] to [Slice Setting]. 66. In the array info of [Monitor] mode, add unit to the field [Stripe Size]. 67. Add messages : "delete slice" and "unmap lun" in event log. 68. In [System Params], add sub-title "Change Password". 69. In [Delete Array] & [Array Info], re-arrange the layout to display [Alignment Offset]. 70. In [System Params], the GUI will display correct week when user inputs a valid date. 71. In [Quick Setup], [Expand Array], and [Disk Info], the GUI don't display the check-box [Select All Chassis] and the button [Chassis X]. 72. In [Update F/W], the GUI will display percentage when the uploaded F/W is writing. GUI server: 1. System restart with Fan/Power or other failures kills server process. 2. Add sending system information via mail. 3. Sending mails with incomplete mail address kills server process, or causes mail lost problems. 4. Fixed problem which caused firmware transfer to fail if the user canceled update and started update again. 5. Fixed vaious problems in System Information mail such as LUN map problem, and added information such as Array info. 6. Show correct Update State when user cancels firmware update. 7. Add file lock mechanism to prevent two users uploading firmware via cgi at the same time. 8. Fixed the problem which caused firmware upload progress to stop, after having uploaded an incorrect file and restart firmware update. 9. Fixed the problem which caused unmount /tmpfs directory fail when uploading an incorrect file. 10. Show correct Update State after the system writes the firmware to the Nandflash ROMs. 11. Fixed problem of showing network error when the user cancels firmware update. 12. Fix problem: If the network was disconnected during writing the firmware to Nandflash ROMs, the system would warn Image Corrupted upon the next system restart. 13. Fix problem: If the user closed CGI browser window during firmware update, the GUI would stop responding. 14. Prevent user from canceling firmware update during writing the firmware to Nandflash ROMs. 15. Fix problem: If the network was disconnected during writing the firmware to Nandflash ROMs, and the user restored connection and restarted GUI, there would be a page data checksum error. 16. Add part of the command for bootcode update. 17. Fix sending empty mails problem. 18. Modify the behavior of IP request from DHCP server. If DHCP is enabled and the server cannot get an IP from DHCP, the server will keep requesting IP for ten times. If the server is unable to get an IP after ten retries, the server will stop requesting for an IP. 19. Fix problem with setting DHCP enable. 20. During firmware update, when the firmware file is being updated to the nand flash, GUI will show the current progress in percentage. 21. Fix [Bootcode Version NO.] on page64. 22. Add Bootcode Update command. 23. Add Time Zone set up. 24. Fix problem which caused the mail sender to receive a copy of every delivered mail in his mailbox. ```````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 103a-0F21 Firmware build : 04/14/2006 firmware release date : 05/03/2006 Issue Description: Raid kernel - 1. Add event log decode rule to record FC929X login/logout event. 2. When "threshold for clone" function is set to disable, the "threshold for swap" function will auto set to disable. 3. Fix a bug of error wording after user input "Lun #" in "Lun Map" menu. 4. Fix a bug of incorrect disk number seen from host side. 5. Update GUI commands and page data to ACSGUISpec1.27_19 - Add BBM fail, over temperature warning 6. Modify firmware polling rules to background read disk temperature via ATA SMART command. 7. Add FC auto ID and auto negotiated data rate in GUI page data. 8. Modify the HardLoopID display rule in "Fiber Info" from "View SYS Info" function. 9. Modify the HardLoopID setting process. 10. Reverse the definition of "Auto ID" setting. 11. Change Auto ID to none on GUI, when the FC channel is unlinked. 12. Fix the problem of reading disk temperature via ATA SMART command after disk hot plug. 13. Modify System Info reported FC Auto ID to show the current Auto ID, and Auto ID is none when FC channel is unlinked. Root file system - 1. Change bootcode checking to allow bootcode downgrade to a previous version or update to a beta version. 2. If the user inputs an incorrect IP for SMTP server to send mails, the sendmail process will keep retrying connection and will not end for a long time; if this happens coninously, the sendmail processes will consume lots of memory. The problem is now fixed by modifying smtp application. GUI server - 1. Add verification of firmware file during firmware update; an invalid firmware will return fail satus during Nand Flash update. 2. Show bootcode update percentage during Boot Rom update. 3. Fix a bug which could cause send empty mail problem. 4. Fix a bug which could cause sendmail problem when the user change SMTP server IP address to SMTP server domain name. 5. Fix a bug about setting mail sender address. 6. Send warning mails when there are voltage warnings. 7. Send Event Log by mail. 8. Fix the problems with Event Log mail delivery, so that over 10Kb messages can be sent 9. Fix the missing byte in the beginning of the Event Log mail messages. 10. Add alternate SMTP server settings. The mails are sent via the alternate SMPT server when there are problems with the primary SMTP server. 11. Fix problem with SMTP server setting, which caused mail delivery problems when the user set SMTP domain name. 12. Fix the problems with some pointers memory allocation. 13. Fix memory leak problem by fixing dynamic memory allocation and un-freed thread resources problems. 14. Auto Shutdown mail messages triggered by Fan Fail should mailed when both fans fail, instead of just one fan fails. 15. Sometimes warning status restoring mail messages are not sent. 16. If user keeps sending more than 10 Event log mail continously in a short period of time, the system will hang. 17. Change the bootcode version for previous bootcode versions or beta versions to "prior to 1.4" to avoid confusion. 18. Allow bootcode downgrade or update to a beta version, also shows beta version name "0.14c" instead of "0.14" 19. Changes made to RTC time on terminal can now be reflected in Linux system time. 20. When RTC is disabled or has failed, mail warning messages to user. 21. Fix the problems caused by the effects of changing RTC time by modifying the mail delivery timer. 22. Add Firmware/Bootcode Update Done status in GUI page data, so that the user would know when it is ok to reboot the system. GUI client - 1. In [Update F/W], the GUI will notify the user to restart the controller and the GUI program after update new System F/W or Boot code. 2. In [Quick Setup], the GUI will show the selected slice correctly. 3. In [Quick Setup], [Delete Array], and [Array Info], the GUI will show the unmap lun to existed slice. 4. In [Modify Array], if user didn't change any properity of slice. The GUI will notify user that there is nothing change after he press the button [Save and Process]. 5. In [Quick Setup], the GUI will show "xxxM" when the slot capacity is less than 1G. 6. In [Event Log], add new function to send out event log and GUI log via mail. 7. Add more event logs and fix the incorrect logs. 8. In [SMART], add new function [Test SMART]. 9. GUI will stay in "Test SMART"'s table after doing Test SMART. And change the "o" to "Healthy" , "x" to "Unhealthy". 10. In [Update F/W], GUI will show correct message when error occur. 11. GUI will change the voltage state button's background to red when voltage error occur. 12. Change the way to judge fan number to display on the monitor mode's environment information panel. 13. Fix bug in [Modify Array] when press confirm dialog's "no" button , the GUI will not send duplicated commands in the next time when press "yes" button. 14. Fix bug to send integrated mail in [Event Log]'s Mail function. 15. Add "Alternate SMTP Server" in [Notify Params]. 16. When close GUI's Applet window, user only need to retry one time to restart program. 17. Add boot code version on controler information panel and change update F/W's message when update fail occur. 18. Change the "secctor" to "sector" and "OFFSET" to "Offset" and "F.S." to "File System" and add border in each slice informaiton in monitor mode's array information panel. 19. Prevent the browser from loading JAR from cache. 20. Change every "Sector Per Track" to "Sectors Per Track". 21. Change the [Disk Info]'s size format and chassis disk info's size format from "0.00" to "0" and "SATA" to "SATA 1" or "SATA 2". 22. In [Disk Info], change the value of fields: "LBA48", "SMART", and "DST" from "o" to "Support" and replace the field "Healthy" with "Status" and change the value of field "Status" from "o" to "Healthy". 23. In [Event Log], the field "Time" will be filled with "--" if the time of the log is invalid. 24. If the RTC is disabled, the GUI will display the following messages: "Warning: RTC is not working!!" and "Please try to set RTC again." when the GUI is starting. 25. For [Auto Shutdown] only: Change "Fan Fail or N/A" to "All Fan Fail or N/A" in [Auto Shutdown]. 26. When select single disk to process "Test SMART", the select state will be clear. 27. In [SanMask Param] to set Mask Command and shown on table properly. 28. Change the " in IP Address format" and " in Domain Name format" to " IP Address format" and " Domain Name format". 29. Add message when user close smtp and would deliever event log mail to notify them. 30. Fix bug when SMTP setting have one group of smtp correct, the command will send without warning. 31. Change the default value when ip mode address is all set to 0, the field will display all blank. 32. Add "Host Channel"'s Data rate "No Link" when "Fiber Channel" is plug out. 33. When BBM system fail or over temperature, the GUI will display red background on environment button "BBM" and change BBM state. 34. The Test SMART table's state field will display blank when SMART mode is disable and GUI didn't act SMART manual. 35. Change the Timer_Arrange's interval to get frequency pages from 1 secs to 3 secs. 36. Change the Timer_Arrange's interval from 3 secs to 1 secs. 37. Add judge if channel type is fiber then detect if fiber channel is plugged out. 38. Change the status to blank when SMART is disable and user just get into the "TestSMART" page. 39. When Fiber channel is plugged out , the channel ID will become "--". Linux kernel - 1. Adjust Linux system time again for more accurate synchronization with the RTC time. 2. Adjust LAN LED lights. `````````````````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 89321Ax104a-1026 Firmware build : 06/15/2006 Firmware release date : 07/06/2006 Issue Description: RAID Kernel - 1. Add Chassis Description (for mail messages) in NVRAM 2. Add SNMP Trap configuration settings in NVRAM 3. Fix the problem which effected manually set Hard Loop ID to become -1 4. Place the lightbar to the correct menu index to reflect the current Auto ID setting, for terminal menu "Auto ID"->"Yes/No" 5. Modify the "Shutdown" function process rule - system halt after shutdown success. 6. Fix LCD warning message display problem which caused warning message on the 2nd line of the LCD to remain after the warning is cleared. 7. Support new battery module (ACS1162). Modified I2C program(delayed 1 ms before issue control data to target I2C device) for battery power start/stop control. 8. Fix problem of FC link failed when download from QC to system code. 9. Fix problem of FC hard loop ID setting issue. 10. Correct problems with displaying messages Set IP, Subnet mask, Gateway, DNS on terminal when DHCP is enabled. 11. Support 2GB memory and working at first 1GB memory range. 12. Modify the process rule for BBM temperature to filter out unreasonable temperature readings. Root File System - 1. Add SNMP application and related configurations GUI Server - 1. Send SNMP traps to inform system status or warnings. 2. When the user enables DHCP, if the system is not able to acquire IP from the DHCP server due to network problems, it will retry until an IP is acquired. 3. If DHCP is enabled, upon system startup, if the system is not able to acquire IP from the DHCP server due to network problems, it will set IP 0.0.0.0. 4. Do not send SNMP traps and warning mails when system is shutting down. 5. Fix the problem which caused disk offline warning mails to be sent upon disk rebuilding, when an Array member disk is plugged in for Array rebuild. 6. Add Chassis Description and Model Name in mails. 7. Send SNMP traps when the temperature on the backplane is over the threshold. 8. Send SNMP traps and mail warning messages when the battery fails. 9. Fix problem: change in Chassis Description does not take effect immediately in mails. 10. Fix problem: when the IP address is acquired from DHCP server, if the user closes GUI and starts GUI again, there will be a connection problem. 11. Modify the rules of automatic DNS IP acquisition. When the user enables DHCP, automatically acquire DNS IP from DHCP server. If the DNS IP is not set, do not automatically acquire DNS IP upon system boot. 12. Modify the format of SNMP trap, so that the user will not have to load MIB file anymore; the trap messages are also simplified for user's convenience. 13. Fix the problem with acquiring the Subnet Mask when DHCP is enabled. 14. Fix the problem which could cause system warning mail messages overflow, and thus cause problems with mail delivery and SNMP traps. GUI client - 1. On [Notify Params] page, Add SNMP configuartions. 2. Add Chassis Description in SMTP configurations. 3. Fix bug the SNMP's HostName and community name which have many squares when there is no words in the string. 4. Fix bug when user choose to disable SNMP, the GUI will return to moniter mode. 5. Fix bug when DNS was not set and get into "ParamNotify" the warnning message will show only once. 6. Add message on "BBM Evironment" to display if Battery is working or shutdown. ``````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 89321Ax105a-1029 Firmware build : 09/06/2006 Firmware release date : 09/25/2006 Issue Description: RAID Kernel - 1. Support "Disk Access Delay Time" function. 2. Fix incorrect MAC Address in GUI page data. 3. Fix system hangup problem when the user performs the "Array Parity check" function on RAID level 0, 1, or NRAID. GUI server - 1. Add System Info Mail function. 2. Fix the problem which caused incomplete Event Log mails. 3. Add information such as RS232, Fiber Info in System Info Mail. GUI client - 1. Fix incorrect BBM status display. 2. Add System information's mail button in [Notify Param]. 3. Add [Disk access delay time] in [System Param]. 4. If SMTP is not set, GUI will prevent the user from sending event log mails and inform the user to set SMTP in [Notify Params]. ``````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 89321Ax106a-112A Firmware build : 12/01/2006 Firmware release date : 01/15/2007 Issue Description: RAID Kernel - 1. Adjust the firmware behaviors to shorten the I/O response time during SMART function execution. 2. Change the firmware handling procedures when the BBM is attached and array is R6 or TP, and the system is abnormally shutdown during Host I/O access. 3. Change the parity generation procedures when the user disabled PreRead, set stripe size to 1024(or 512) and created a parity based Array for Array parity check, Array init, or Host I/O access applications. GUI CLient - 1. Notify the user to set SMTP mail account, if the user attempts to send event log mail without having set SMTP already. 2. Correct the display of hexadecimal numeric values display on the event log. ``````````````````````````````````````````````````````````````````````````````````````` 89321 Firmware Release Note: Ver: 89321Ax107a-112C Firmware build : 03/06/2007 Firmware release date : 06/12/2007 Issue Description: GUI Server - 1. Modify the format of mail header to make it RFC compliant, in order to fix the problem which caused mails to be displayed incorrectly when mails are sent via Exchange mail server. 2. Fix the problem which caused the time in the mail to be 1970/1/1 0:0:0 when a warning status is cleared. 3. Fix the problem which caused the time in the mail to be incorrect when the time zone settings are changed. 4. Fix the problem caused by System Info mail when the content of system information is too large in size. 5. Fix message format problems, including the time string, alignment, etc. Also, System Info mail no longer displays disk temperature when the SMART function is not enabled. (Previously displayed temperature 255 if SMART had not been enabled.) ```````````````````````````````````````````````````````````````````````````````````````